Road Vehicle GPS Speed Limiter Ethiopia Standard With GPS Tracking Three In One

. Product Function:

1. Fixed maximum speed limiting: Set a maximum speed according to the actual needs of vehicles. For example: if you require the vehicle speed does not exceed 60Km/h (or other appointed speed), the product will strictly control the vehicle speed does not exceed 60 Km/h (or other appointed speed) ;
2. GPS speed data collection data collection ;
3. Vehicle pulse speed ;
4. Digital display controller adjustment.

Preface :
If you want to achieve fast installation, you need to find a installer very familiar with
this vehicle type, because the circuit wiring has huge difference fordifferent vehicles.
For example, now you want to install limiter for bus, you can not find a maintainer
forprivate car, you must finda professionalmaintainerforbus. In ourpastexperience,
only a veryprofessional installer can find the lines fast and installthe limiterfast.
Please note this point is very important!
In addition, we also recommend that the installer read this instruction carefully
before installation, if he can not understand the instruction very well, please
communicate with us, it can improve the installation efficiency effectively .

2. Technical Parameters:

Road Vehicle GPS Speed Limiter Ethiopia Standard With GPS Tracking Three In One

1. The Lines Definition:
2. Electronic Mechanical Throttle Vehicle Truck Over Speed Limiter In Kenya

4 At first, we adjust the voltage value of the brown wire to the low value we measured form the accelerator pedal signal wire. ( The value of the actual measured voltage prevail. ) Then we adjust the voltage value of the white wire to the high value we get form the accelerator pedal signal wire. ( The value of the actual measured voltage prevail. )

Then , we can dot a little red glue onto the adjustable knobs to fix it, in order to prevent the adjustable knobs may appear small rotation in the long vehicle driving.

5 Connection Diagram for Mechanical throttle

The Specific install Steps:

①　Place the limiter host.

The limiter host can be installed in steering room ,a place will not not affect the driver operating. Please pay attention to fix it well, make the lines routing as hidden as possible.

②　Install the limiter actuator and connect its drawing cable to vehicle throttle cable.

At first, we connect the actuator power line well, turn on the power, the actuator will spit its steel cable automatically , turn off the power until the cable completely spit out.

Then please step the accelerator pedal to the end state. Make the pull head of the actuator cable pass through the engine throttle control lever. Then cut off the excess portion, fixed the cable head well, make the drawing direction of the limiter steel cable and vehicle throttle cable negative, then fix the limiter well, there is a mounting bracket on the limiter body. Please install it in a appropriate position onto the vehicle with screws.

Mechanical actuator is used to control the throttle valve opening, when the vehicle speed in the normal range, the mechanical actuator will be in standby state, will not interfere the driver’s throttle operating. When the vehicle is in over speed state, the actuator will begin working, it will make the throttle valve mouth get smaller compulsively. The driver should not vigorously stamping step on the throttle. We shall not be responsible for the damage caused by this deed.

Note: You should choose the actuator model according to the working voltage of vehicle battery. So please tell us the vehicle voltage at first.

③　Connect the control wire of the limiter actuator to the limiter host, and connect the power line and ground line for the limiter actuator.

④　Connect the power line,ground line, ACC line, left-turning signal line, right-turning signal line, vehicle speed sensor signal line to the original vehicle lines one by one.

Road Vehicle GPS Speed Limiter Ethiopia Standard With GPS Tracking Three In One

3) The Installation Test Method:

①　Start the vehicle normally, stepped on the accelerator pedal, to check if the refueling is in normal state.If OK ,it means installation well,otherwise failure.

②　In the refueling process, slide the switch (which is on the PCBA board) to the “close” end, then step on the accelerator pedal, if fueling is failure, it means the installation is successful, otherwise failure.

③　Wait about 3-4 seconds, then slide the switch (which is on the PCBA board) to the “broke” end, then step on the accelerator pedal, if you find refueling is in normal state, it means the installation is successful, otherwise failure.

Note: the above test process should not appear the phenomenon of stalling or automatic fueling. If appears, it means some problems exist.

if the test situation are the same with the above description, we preliminary estimate the connection and the adjusted idle voltage is right. To ensure the 100% right installation, we suggest that the driver take actual road driving test.

1. We provide web tracking system, Android APP and IOS App free
2. Our device can send data to your own server, we will provide SDK and API for integrate (sample source code:C/C++,Java,C#)
3. we will install the tracking system into your server if you have the own server
4. We provide OEM and ODM services, it is free if you only add logo and company name
5. Warranty: 24-month