Plastic Emergency Rescue Equipment Semi - Automatic Door Opener

Description

This device is powder-powered door opener and composed of breaking door tool, breaking lock tool and break-in tool. It is widely used for public security, police, fire-fighting and highway rescue departments to break door or lock in emergent situation. This device uses 0.27 inch caliber bullet as power and can continuous fire 10 bullets to break max. 12cm diameter iron bar.

Specification

Operational Process

A.Reload the bullets

Insert the loaded cartridge clip from the hole under the lock breaker's grip into the gun from bottom to top until the first bullet is at the firing position. When in use, the bullet can be fired by pushing the target object board against the perforated template.If there is no firing, keep pressing the working face tightly for 30 seconds, then you can pick up the door gun and resupply the ammunition.Hold the front sleeve with your hand and pull it forward in place to make the piston return to position, then back in place to complete the top of the next round.Do this until the cartridge holder is empty.

B.Actuating arm

The drive rod is designed to break the lock and is able to penetrate the lock sleeve up to a distance of about 7cm to disable the lock.After the lock sleeve has failed and the key path has been pushed, the bolt or lock bolt is removed from the door frame or blocked.This can be accomplished by using a small screwdriver or flat piece of steel to slide back or turn the bolt.In many cases, the force of the door breaker opening will break the lock bolt or lock and open the door directly.If the door does not open, use a small screwdriver or flat steel plate to turn it, or pull the locking bolt back and force it open, or push with the shoulder.

Padlock: point the breaker directly at the top of the lock body, breaking the internal parts so that the clasp can be moved.

Motor vehicle door lock: the use of the lock breaker is easy to make the motor vehicle above.

For example, when an injured person is trapped in a car, breaking a window to get in May cause serious damage. In this case, a latch breaker is ideal for unlocking.

C.Fly chisel

The flying chisel can penetrate doors and other objects with a thickness of 7.5 cm.This penetration enables the device to lower through the door and break the locking bolts behind the door.The chisel can penetrate most of the wooden doors, for example, baotou steel wooden doors and residential security doors.

Open the latching screw lock: place the chisel along the door or in the vertical position, place the chisel between the lock handle (or lock face) and the door edge, and directly break the latching bolt.But if the door is steel or steel, do not put the chisel in the door and the door between the cracks, ready to start the tool, and the door to maintain a vertical Angle.

Door handles: in some cases, breaking or cutting the handle will expose the internal parts of the handle.According to the handle design, use the lock breaker to push out the inside parts.

Door lock: when it is known that there are other locks on the back of the door, the lock breaker can be very effective in breaking the back lock with a flying chisel.

D.Cut off

The flying chisel is designed for cutting screw heads and steel bars.In special cases, it is required to remove the bottom shear screw head or steel bar with multiple guns.When cutting off the bolt, the chisel should be avoided to use in the welding seam or welding repair.

Cutting bolts, screws, rivets, pins and steel bars: press the chisel directly on the side of the object to ensure that the tool will not slide open when starting. The best effect is to slightly tilt the cutting surface at an Angle of 75 to 80 degrees. Cutting larger bolts may require more than one shot.Be careful not to stand next to the muzzle of the gun, as the bolt or pin to be cut may bounce off and splash a certain distance, so it is important to wear eye protection when cutting bolts, screws, rivets and pins.

According to the type and thickness of the material, the flying chisel can cut off the window bar very effectively. When cutting off the window bar, the first thing to pay attention to is whether the bolt is outside, which is easier to move the window bar.If inside, aim the gouge at the intersection or close to the end of the steel bar and cut off the bar. This may take several shots.

Note: when using, you must aim at the target and press hard, otherwise there may be stink bomb, which will affect the effect of using.

About Us

Beijing Heweiyongtai Sci & Tech Co., Ltd. was established in the beginning of 2008. We are a hi-tech enterprise specializing in supplying and trading Security Inspection equipment, EOD equipment, Anti-terrorism equipment, Intelligence device, etc. Our products are widely applied in public security bureau, military, custom, government security agency, airport, exhibition, etc.

Our company headquarters and showroom are located in Beijing, the capital of China. There are more than 400㎡ showing room where exhibits nearly hundred kinds of well-equipped products and equipments. Our staff are all qualified technical and managerial professionals to provide you satisfied service.

Our main products and equipments are as follows, and is increasing:

★EOD Equipment
★Security Inspection Equipment

★Anti Terrorism Equipment

★Investigation Equipment

Our factory Jiangsu Hewei Police Equipment Manufacturing Co.,Ltd was established in the year 2010.

We establised research centre and factory in Shenzhen in the year of 2014.

Overseas Exhibitions

If have any inquiries about our company or products, please contact the following information.