KS F ISO 1182 Building Materials Flammability Tester Non-Combustibility Tester For Noninflammable Material

Building Material Flammaility Testing Equipment Incombustible test furnace

Product description

Building materials non-flammable test furnace is designed and produced according to GB / T5464-2010 / ISO1182: 2002 standard. It is used to test non-flammability of the main components of homogeneous building products under specific conditions.

Technical parameters

Test methods

1. So that the furnace temperature equilibrium, if the logger can not be calculated in real time, the final temperature should be checked whether the balance.

2. Before the test should ensure that the entire device is in good working condition, such as a steady flow clean air flow, the device can be smoothly inserted into the slide, the sample holder can be accurately located in a predetermined position in the furnace.

3. Prepared according to a predetermined and regulated by the state of the sample into the sample holder, the sample racks suspended from the support member. The sample holder into a predetermined position in the furnace, the operation time should not exceed 5s. When the sample is located in a predetermined position in the furnace, immediately start the timer. Recorded during the test furnace thermocouple temperature measurement, such as the requirement to measure the surface temperature of the sample and the center temperature, corresponding to the temperature it should also be recorded.

4. Carried 30min test, if the furnace temperature reaches the final equilibrium temperature in 30min, that is measured by a thermocouple temperature drift (linear regression) within 10min of not more than 2 ℃, you can stop the test. If unable to reach equilibrium within 30min, the test should be continued, while every 5min check whether the final temperature equilibrium, when the furnace temperature reaches a final equilibrium temperature or testing time reaches 60min end of the trial should be. Recording duration of the test, the sample holder and then remove from the heating furnace, the end of the time trial for the end time of the last 5min or 60min. Temperature should be checked after the end of the test record if the logger can not be recorded in real time, test. If it can not meet the above requirements, it should be re-tested. If an additional test using a thermocouple, the thermocouple should all have reached the final temperature equilibrium or when the test time was 60min when the end of the trial.

5. The collection and after the test specimen cracked or falling all carbides, ash and other debris, together with the sample into the drying vessel was cooled to ambient temperature, weigh the residual mass of the sample. The quality of each sample were recorded before and after the test and observing the combustion behavior recorded during the test specimen. Sustained fire occurrence and duration records, accurate to the second. Sample shows a continuing 5s or longer continuous flame on the surface it should be regarded as sustained fire.

6. The following furnace thermocouple to measure the temperature, in degrees Celsius, the initial furnace temperature T1, average temperature last 10min predetermined temperature balance of the furnace; furnace maximum temperature Tm, the maximum temperature throughout the test discrete value; the final furnace temperature Tf ,. The temperature during the test last 1min average.

Fourth, the end of the trial, finishing the test furnace wipe clean for the next use.

What is a non-combustible?

Non-combustible materials are building materials that do not burn or ignite when subjected to expected levels of fire or heat. Examples of non-combustible materials include brick masonry, concrete blocks, hardy backer board, calcium silicate board, cement board, metal, and certain types of glass.

SKYLINE (DONGGUAN SKYLINE INDUSTRIAL CO.,LTD) provides full line of Toys Testing Equipment, Fire Testing Equipment ,Flammability Testing Equipment,Tensile Test Machine, Furniture Testing Machines ,Textile Testing Equipment and other lab test equipment .We also offers value added support services like lab layout, calibration testing procedures / standards, recording techniques and operations of equipment, etc. We have agents to support you in over 10 countries around the world. With a network of representatives providing sales and technical support world-wide.

SKYLINE has achieved good repute in the fields of Fire Testing Equipment, Footwear Testing Equipment, Toy Testing Equipment, Furniture Testing and other lab test equipment.

SKYLINE focus on the lab testing equipment for decads and  we manufacturers the testing instrument as per the international standards like EN71, ASTM, IS 8124 and SRS.

Our major customers are BV, ITS, TUV, SGS, Hasbro and SASO, For these customer 100% testing instruments are supplied by SKYLINE and we are the continuous supplier for these lab. Since SKYLINE is a manufacturer design/develop with advanced technology and having well experienced Technicians which will provide high quality service after sale.

Our main products

Lab Testing Equipment

Flammability Testing Equipment

Fire Testing Equipment

Wire and Cable Fire Tester

Building Material Fire Tester

Toys Testing Equipment

Environmental Test Chamber

Textile Testing Equipment

Furniture Test Machine

Mattress Testing Machine

Temperature And Humidity Test

Our Service

Testing Equipment Design and manufacture

Test Lab Planning and Establish

Toys Test Equipment Upgrade

Toys Test Equipment operation Training

Toys Finish Goods and Mattress  Inspection

Acting for Customer Testing and Certifying

Acting for Foreign Trading Company Quality Inspection

Please have a look at our website and don’ t hesitate to contact us if any items catch your interest. We will do our best to meet your requirement.
Thank you for visiting. We look forward to your inquiry to carry forward win-win cooperation with you soon.